Inquiry

Rotor & stator.

Premium quality, worldwide delivery. Hard-chrome rotors, standard stators, complete sets — compatible with all major brands.

40 products

Rotor and stator are the pumping pair of every progressive cavity pump: a hardened steel screw turns inside an elastic sleeve and pushes the mortar forward in even chambers. No other component of a plastering machine has such a direct effect on output, pressure and service life — and no other part wears out as fast.

How rotor and stator work together

The rotor is a helical shaft; the stator is an elastomer sleeve with a matching internal profile. As the rotor turns, sealed chambers form between the two and travel from inlet to outlet. Because these chambers keep a constant volume, the pump delivers evenly and without pulsation — the basis for a clean spray pattern on the wall.

For this to work, the rotor has to sit in the stator with a defined preload. Too little preload and material slips back, output drops. Too much and power draw and temperature rise, and the sleeve wears out within hours. That is why rotor and stator are always treated as a pair and are usually replaced together.

What D6-3, D7-2.5 and D8-1.5 mean

The designation describes the geometry of the pumping pair. The first number stands for the size, the second for the number of stages. The basic rule: more stages mean more pressure and longer conveying distance at lower volume; fewer stages mean more volume over a shorter distance.

In practice, a D6-3 works against long hose runs and upward to higher floors, while a D8-1.5 places a lot of material in a short time. A crew pumping floor by floor in interior work chooses differently from one spraying large areas at ground level.

Which pumping pair suits which material

Gypsum plaster and gypsum-lime plaster run easily and do not need extreme pressure — volume is what counts. Lime-cement plasters are more abrasive and stiffer; they put much more load on the sleeve and benefit from a pressure-oriented design. Lightweight plasters with perlite or EPS aggregates tend to separate when pressure gets too high.

Screed and cement mortar are the toughest case: large grain size, high abrasion. Here the quality of the sleeve material decides the service life, not the design. Anyone pumping screed regularly should budget the stator as a wear part, not as a spare part.

Spotting wear before the job site stops

A worn pair gives warning. The first signs are a noticeable drop in output at the same speed and a spray pattern that becomes uneven. If pulsation appears at the outlet, the pump is already working against backflow.

A second, often overlooked sign is power draw: if it rises for no obvious reason, the rotor is too tight — usually because the sleeve has swollen or hardened. If the pump runs unusually easily and hot, the clearance is too large. Both are reasons to change the pair before the motor is damaged.

Clampable, slotted or SPIRAL — the designs

Clampable stators can be readjusted with a clamping mechanism. This noticeably extends usable service life, because early wear can be compensated instead of replacing the part straight away. Slotted versions also make changing the stator on site easier.

SPIRAL sleeves have a modified internal geometry that guides the material flow more evenly and spreads abrasion over a larger surface. Whether it pays off depends on the material — clearly with abrasive plasters, hardly with pure gypsum plaster.

Compatibility

The common sizes are standardised across manufacturers. A D6-3 pumping pair therefore fits machines from different brands, as long as the connection and the anti-rotation lock match. Our parts are designed for the most widespread machines on the market — including PFT G4 and G5, m-tec Duomix, Putzmeister MP25 and Uelzener Putzknecht.

When in doubt, the size and the type of anti-rotation lock matter, not the machine name. If you have the old part at hand, you will find the right replacement fastest: read the size, compare the design, order.

Häufige Fragen

How do I know the stator is worn?

Output drops at the same speed, the spray pattern becomes uneven and the outlet starts to pulsate. If power draw rises as well, the rotor is too tight — that is also a reason to replace it.

Do I always have to replace rotor and stator together?

As a rule, yes. Both wear together, and a new rotor in a worn sleeve no longer reaches the required preload. Replacing only one part is worthwhile only if the rotor is visibly undamaged and has run for a short time.

How long does a rotor stator pair last?

It depends almost entirely on the material. With gypsum plaster several hundred operating hours are common, with screed and cement-based plasters considerably fewer. Running dry, on the other hand, destroys a sleeve within minutes.

What does D6-3 mean?

The first number stands for the size, the second for the number of stages. More stages mean more pressure and conveying distance at lower volume; fewer stages mean more volume over a shorter distance.

Which pumping pair fits my machine?

What matters is the size and the type of anti-rotation lock, not the machine name. Read the designation on the part you removed — or send us a photo and we will identify the right part.

What is the benefit of a clampable stator?

It can be readjusted. Early wear is compensated instead of replacing the stator straight away — this extends usable service life and lowers the cost per square metre.

👋 How can we help?
Choose your preferred way:
Find a part by photo
AI identifies it in seconds
WhatsApp
Response < 1 hr
Email
info@stock-intertrade.com
Live advisors available (4)